Chinese translation for "load curve"

负荷的曲线
负荷曲陷
负荷曲线；钻压曲线
负荷曲线图
负载曲线
载荷曲线
载重曲线,负荷曲线
钻压曲线

Example Sentences:

	1.	The unloading curve normally falls below the loading curve to form a hysteresis loop . 卸载曲线通常都落在加载曲线之下，形成一个滞后回线。
	2.	Upon unloading at any state in the deformation, the strain does not retrace the loading curve but is reduced along an elastic unloading line . 在变形的任一阶段卸载时，应变都不按加载曲线返回，而是沿着弹性卸载曲线下降。
	3.	Monthly load curve 月负载曲线
	4.	Annual load curve 年负荷曲线
	5.	It is shown that permitted load curve must be implemented in choosing crank press 在选用压力机时，必须严格按照许用负荷曲线图来选择。
	6.	Combining it with the standard daily load curve can make the mean daily forecasting error with in 2 % 将其与标准日负荷曲线取平均作为预测结果，示例表明日平均误差小于2 % 。
	7.	With the proposed method , the internal operation of lijiaxia hydropower station is optimized and the optimized load distribution is derived based on three characteristic daily load curves 运用上述方法，分别以3条特征日负荷曲线为依据对李家峡水电站的厂内运行进行了优化，并得到其负荷分配方案。
	8.	By effectively managing and controlling of electric load , we can improve load curve and advance using rate of power supply equipment , which can prevent from drawing strobe and limiting electricity and avoid affecting social produce and life 对用电负荷进行有效的管理和控制可改善负荷曲线，提高发供电设备的利用率，可防止拉闸限电，避免影响社会生产和生活。
	9.	This software can not only measure the real time data of hydroelectric plant , but also carry out the auto generate electricity on the hydroelectric plan t and ordinal startup - stop of the dynamotor . the software also carrys out the functions of alarm disposal , report forms , print and load curve 该软件不仅实现了对水电站内各种模拟参数和数字信号的实时监测功能，还实现了对水电站的自动发电、机组顺序启停的控制，以及报警处理、报表打印、负荷曲线等功能。
	10.	In different in terne die travel , the metal flow characterize in warm extrusion forming processes and the affection for the flow of metal stage which made by the difference between the blank bottom altitude and the axial direction limiting size in warm extrusion forming technique have been analysed we have gotten the equivalent strain field and the velocity field and other field variable that the blank in different in terne die travel and the die travel - load curve . . at the same time , we have analyzed the contributing factor for the oil pump stator forming process optimized and achieve thereasonable die parameter for the war m extrusion forming finally , the optimized technics parameters were used into pilot production , then the qualified oil pump stator forging were produced , the analog results were compared with those of pilot production 论文具体分析研究了不同成形工艺过程中金属流动的特点，并对不同凸模行程下温挤成形过程中的金属流动特点、坯料连皮厚度(底部高度)与温挤压成形工艺中的轴向界限尺寸的差值对金属变形阶段的影响进行了分析，获得了坯料在不同凸模行程下的等效应变场、速度场等场变量及凸模行程-载荷曲线，同时对油泵定子成形过程的影响因素等进行了分析，优化并获得了合理的温挤成形工艺及模具参数。最后，利用模拟优化获得的各项工艺参数进行生产实验，得到实际生产出的合格油泵定子件，并将模拟结果与生产实验结果进行比较。

Similar Words：

"load controller" Chinese translation, "load criterion" Chinese translation, "load cross line" Chinese translation, "load cross-line" Chinese translation, "load current" Chinese translation, "load custom ui" Chinese translation, "load custom ui scheme" Chinese translation, "load cycle" Chinese translation, "load cycling" Chinese translation, "load data" Chinese translation